2017年2月9日星期四

Fault Treatment of Hot Water Submersible Pumps

1. Hot water submersible pumps operation occurs vibration
1. Unstable pipe support, pump base or anchor bolts loose is a common cause of vibration, you must tighten the bolts around to avoid loosening.
2. Gas inside the liquid, carefully check the water pump and water inlet sealing surface of the connecting bolts are loose, the gasket is damaged, pump and piping system components have been damaged.
3. Hot water pump and the motor shaft is not concentric, should be adjusted with the belt rotation, the rotation belt too loose or bad contact, can also cause vibration. Impeller impeller is not running in the impeller wear or impeller flow channel blockage can easily cause vibration, sometimes because of the axis of bending impeller impaired balance caused by vibration.
2. Hot water submersible pumps running noise increases
1. Bearing noise: sound source bearing installation parts, generally with an iron bar or screwdriver to live bearing installation parts, with the ears, for the crash crashed sound.
Motor noise: generally wailing, can only replace the motor.
Cavitation noise: sound source in the pump cavity, crackling crackling sound. Third, the motor hot Chinese pump technology forum
The outer wall of the motor may be hot and may run with super current. The valve may be closed with a small outlet. The motor may be replaced if it is operated within the rated current or the quality of the motor coil.
2 rotating parts friction, frictional resistance increases, it may overheat the motor should be hot to check whether the rotor is flexible.
Motor bearing at the heat, may be bearing oil or damaged, need to repair or replace the bearings.
The operating voltage is too low, check the circuit to adjust the voltage.

Technical maintenance of hot water submersible pump

Hot water pump and motor because the use of water, if the technical performance can not meet the requirements, not only can not pump, but also may cause accidents, it must pay attention to hot water submersible pump maintenance and repair.
1, often check the seals
Hot water submersible pump internal water, it will cause the motor short-circuit burned out, so each time before use, must be a variety of submersible pump seals to check and found loose in time to tighten, if the seal is damaged, should be replaced . Submersible pump for every 50h after, it should be raised to the ground, the seal to be checked to ensure the use of safety.
2 Timed replacement of lubricating oil
Oil-immersed submersible pump work 500h, should replace the seal chamber of oil. After one year of operation, replace the oil in the motor housing. And should pay attention to the brand of oil, submersible pumps used oil is generally 5 or 10 oil. Different grades of oil can not be mixed. Wet submersible pump running 2000h, the need to replace a lubricating oil, the replacement of the lubricating oil for the lithium-based grease, can not use calcium-based grease.
3, regular derusting
Hot water submersible pump to use a year after the corrosion should be checked, remove the rust, and coated with a layer of anti-rust paint, to be protected.
4 regular maintenance
After 2 years of use, the submersible pump should be thoroughly inspected, folded, and inspected, cleaned, lubricated and reassembled.
5 Storage and maintenance
Long-term hot water submersible pump, do not immerse in water, should be referred to the ground, dry water stains, hanging in dry and ventilated room.

Hot water submersible pump advantages

Relative to the traditional products, hot water pump more energy efficient, but also higher efficiency. Many manufacturers are constantly improving their products, some of which products contain the technology has also developed by leaps and bounds to promote the overall development of China’s industry and growth. According to the requirements of many buyers, pump valve network also summed up the hot water submersible pump some specific advantages.
Advantages First, energy saving more environmentally friendly. Hot water submersible pump energy consumption has always been a matter of concern, the current energy-saving products on the market is more popular, and its utilization is also higher. Comprehensive energy efficiency ratio can reach three to six times, and run-time environmental protection and non-toxic, is very suitable for our purchase.
Advantages Second, the use of more secure. Products are the use of a new operational technology, in the course of the use of products to ensure the safety. Traditional products prone to corrosion, explosion, etc., in the new hot water pump has also been improved, does not appear similar to the situation, an increase of the production life. If you want to know more hot water pump products and prices, please log in directly
Advantages Third, the maintenance more convenient, cost savings. The new hot water submersible pumps have a longer life, manufacturers of products is also a long quality assurance and after-sales, you can feel at ease to buy. As long as it is in accordance with the normal operation of the use of methods, there will not be much of a problem, maintenance is also quite convenient, manufacturers completely help you solve the maintenance problems. Valve trading network is also more types of products, you can compare according to their needs to buy, site customer service will help you identify and select to ensure that the interests of consumers is not compromised.

Prevention and treatment of fountain pump freezing

The northern region of the water system used mostly fountain pumps for the self-priming pump, a winter easy to ice, for this situation we should take the following measures on the water pump on the line maintenance.
1. The fountain pump water emptying, when used with water. To prevent the freezing of water pump pump freezing.
2. If the fountain pump freezes, use hot water or boiling water to pump into the ice. Or heat the pump housing.
3. Use a downhole pump. Fountain pump will be placed underground, the general underground pump deep from the ground, will not freeze.
4. The use of insulation-type pumps. Add the insulation to steam or hot water. To prevent the pump from freezing.
5. Using non-self-priming centrifugal pump. Use, add water can be.
6. Place the pump in an ambient temperature environment. Below zero.

The following six note for the winter pump. To a lot of maintenance to prevent cracking water pump, shorten the life of the pump.

Features of Stainless Steel Submersible Pump

Stainless steel submersible pump is a beautiful appearance, the surface bright as a mirror, feel tough and cold, is more avant-garde submersible pump type. Stainless steel submersible pumps are 316 and 317 stainless steel two, these two kinds of stainless steel pumps have their own advantages, the following specific analysis of the difference between the two.
316 and 317 stainless steel is better than 310 and 304 stainless steel, 316 stainless steel is more widely used, it has good corrosion resistance, often used in marine environments. This is because 316 stainless steel is not only resistant to marine erosion, but also to avoid corrosion of industrial atmosphere.
In welding, 316 stainless steel welding performance is more good, you can use standard welding methods to welding, welding time to take into account the use of the choice of different welding materials for welding. The use of 316L stainless steel does not require post-weld annealing. Heat resistance, 316 stainless steel has a strong resistance to oxidation.
316 stainless steel has the above mentioned advantages and widely used in heavy industry, light industry, household goods and construction industry, if you want to buy stainless steel submersible pumps, then it can consider the purchase of 316 stainless steel submersible pumps. Do not be cheap to buy to inappropriate products, otherwise it will affect the use of submersible pumps, but also for future maintenance and replacement equipment to bring great trouble and unnecessary cost.

Hot water submersible pump instructions in winter

Hot water submersible pump is an essential equipment for extracting high temperature water. Can also be used for ponds, tanks, pressurized use. Specific can be used for hotel hot springs underground water, district heating.

Scope of application
For enterprises and institutions such as: hot spring bath, residential heating, geothermal energy companies use power generation, extraction of underground hot water, according to different calibers we have different specifications for the user to choose models. The device low noise, high efficiency and save energy.
Technical Parameters:
1: Allowable operating water temperature range: +5 to +105 ℃
2: Solid impurity content (mass ratio) is not more than 0.01%
3: PH value (pH) 6.5-8.5
4: hydrogen sulfide content of not more than 1.5mg / L
5: chloride ion content of not more than 400mg / L
6: crew must completely invade the water work. Vertical use, select the model diameter and pump models to match, should not use large diameter diameter of the small diameter of the pump, this is not conducive to the motor cooling.
Motor parameters
Submersible motor lead length: 3m. If you need to extend the cable can call us in advance, submersible motor water lubrication, the use of the motor cavity must be filled with clean water, (Note: be sure to fill otherwise will reduce the motor life) If you forget to add water motor will Rapid burnout.
Motor protection class: IPX8
Electromagnetic wire adopts high temperature waterproof wire.
power supply
380V, the deviation does not exceed ± 5%, the frequency of 50HZ, the deviation does not exceed ± 1%, if the customer needs special voltage or special frequency need to inform us in advance.
material
Impeller: cast iron HT200, or tin bronze (various brands) such as: ZCuSn3Zn8Pb6Ni1
Pump housing: cast iron HT200, or stainless steel such as: 2Gr13. 304 316
Pump shaft: cold-drawn steel chrome-plated, or stainless steel 2Gr13 (1050 ℃ quenched and tempered to enhance the torque)
Motor Seal: Rubber Seal O-Ring; Machine Seal.
Motor expansion regulating bladder rubber material.
Equipment advantages
– 1: Careful assembly at the factory ensures fast and reliable installation on site
– 2: single-stage impeller or multi-stage impeller in series, the noise is minimal. Temperature performance, long life.
– 3: the crew can completely invade the water work, to avoid the vacuum pump easy to enter the air is not easy to use the drawbacks,
Scope of supply:
Hot water submersible pump unit (including the pump and submersible motor composed of two parts), the outlet matching flange one, 12 × 60 bolts 6. Or configure the corresponding outlet (for users to install hose), the use of maintenance manual 1, 1 copy of certificate of packing list, wooden box packaging.

2017年2月8日星期三

Fountain pump electrical installation matters

Fountain pump electrical installation should pay attention to what needs?

1, three-phase fountain pump cable selection of three-phase four-core, one of the yellow-green and white core wire to ground, to a reliable grounding. If there is no fixed ground, you can use 1.5 meters long metal rod buried in the wet soil as a ground, the other three front connected to the three-phase power supply can be.

2, the power supply voltage fluctuation range of ± 10% of the additional voltage, or will shorten the motor life or burn out. If the fountain pump to use away from the power source, you should bold the power transmission line useful section, or will not work.

3, wire connection and wire selection, please read the instruction manual, in accordance with the requirements of manufacturers to purchase, to ensure that the fountain pump work.

4, in the installation process have doubts, please contact the manufacturer as soon as possible to help solve the problem.