Hot water submersible pump motor is mainly submerged in water-based motor; will be installed within the lightning protection device, * thermal protection, * using electronic starter.
① no centrifugal switch, no capacitance, to avoid mechanical wear and tear, increase the number of starts, reduce the volume.
② stator outer stainless steel welding, with stainless steel lining, filled with epoxy resin sealed. Sealing performance, corrosion resistance, heat fast, anti-deep-water pressure, long life and reduce costs.
③ fully enclosed squirrel cage rotor, high-quality copper tank, before and after the copper-ring welding, not easily deformed or broken, conductive properties, and high efficiency. Steel by chemical treatment does not rot.
④ With thrust bearings, can carry a greater axial load, said by the Fen Shuo said stone attack Ru field maintenance.
⑤ motor by the water lubrication, internal and external water cooling, the use of water environment to avoid pollution. Normal working dive depth of up to 900 meters, to solve the domestic deep-water operations and scientific research problems.
* Refers to the single-phase two-wire motor is equipped.
For proper installation, please read the instruction manual carefully before use. Power and fittings must be installed in accordance with local and international codes. All metal fittings and hot water submersible pump motors should be grounded. All ground cables shall be not less than the specifications of the motor cables. External power cord to be greater than the motor, seven sources lead wire, then the product must be absolutely sealed. Be sure to use within the rated voltage range, if the voltage high and low, hot water submersible pump motor will not work. To reduce the risk of electric shock, do not connect the power cord during use or in the water. Do not use the submersible pump in the swimming area.
2017年1月12日星期四
Hot water submersible pump operation and maintenance and storage
Hot water submersible pump operation and maintenance and storage is very important, but also an excellent way to extend the service life, six months of normal operation suddenly a problem, said the quality of hot water submersible pump not, most of the time we ignore the very small The details, we share the following to maintain a small hot water submersible pump details.
1, Hot water submersible pump operation and maintenance:
(1) hot water submersible pumps should be used within the specified range, hot water submersible pump flow must not be too large. When the scope beyond the provisions, likely to cause hot water submersible pump rotor channeling, ammeter swing, the longer the work will result in a serious pump for bad, on the contrary, the pump flow and not too small, otherwise it will increase the downward axial force, So that the life of the entire unit affected.
(2) 8 hours in operation should be fully checked once, ammeter and gauge instructions are significant changes in the operation, whether there is a voice, the normal working current should not be greater than the motor nameplate on the specified rating.
(3) the operation should always check the safety protection device instrumentation reliability and correctness.
2,Hot water submersible pump overhaul:
One of the following conditions should be shut down for maintenance:
(1) hot water submersible pump running in the steady operating point, while the current exceeds the specified value or a sudden reduction in traffic.
(2) Insulation resistance is low (in the case of thermal state should not be less than 0.5MΩ).
(3) the unit in the operation of abnormal noise or vibration.
(4) power supply voltage and frequency are not up to the requirements.
3,Hot water submersible pump storage:
(1) hot water submersible pump should be stored within the storage of water, the surface wipe, coated with anti-rust oil.
(2) for the long-term suspension of hot water submersible pumps, to professional and technical personnel under the guidance of open, naturally dry, with the parts coated with rust oil, non-coated with anti-rust paint parts.
(3) Within one week after hanging out the well, the unit should go into the well, unscrew the water hole and water hole of the motor, and put the water into the net.
(4) such as in the winter, hot water submerged pump hanging out of the well is still down to use, release the internal storage of water, storage location overflow of not less than 0 ℃, to prevent residual water within the body to freeze
1, Hot water submersible pump operation and maintenance:
(1) hot water submersible pumps should be used within the specified range, hot water submersible pump flow must not be too large. When the scope beyond the provisions, likely to cause hot water submersible pump rotor channeling, ammeter swing, the longer the work will result in a serious pump for bad, on the contrary, the pump flow and not too small, otherwise it will increase the downward axial force, So that the life of the entire unit affected.
(2) 8 hours in operation should be fully checked once, ammeter and gauge instructions are significant changes in the operation, whether there is a voice, the normal working current should not be greater than the motor nameplate on the specified rating.
(3) the operation should always check the safety protection device instrumentation reliability and correctness.
2,Hot water submersible pump overhaul:
One of the following conditions should be shut down for maintenance:
(1) hot water submersible pump running in the steady operating point, while the current exceeds the specified value or a sudden reduction in traffic.
(2) Insulation resistance is low (in the case of thermal state should not be less than 0.5MΩ).
(3) the unit in the operation of abnormal noise or vibration.
(4) power supply voltage and frequency are not up to the requirements.
3,Hot water submersible pump storage:
(1) hot water submersible pump should be stored within the storage of water, the surface wipe, coated with anti-rust oil.
(2) for the long-term suspension of hot water submersible pumps, to professional and technical personnel under the guidance of open, naturally dry, with the parts coated with rust oil, non-coated with anti-rust paint parts.
(3) Within one week after hanging out the well, the unit should go into the well, unscrew the water hole and water hole of the motor, and put the water into the net.
(4) such as in the winter, hot water submerged pump hanging out of the well is still down to use, release the internal storage of water, storage location overflow of not less than 0 ℃, to prevent residual water within the body to freeze
Application of electrostatic paint coating for pump subassembly of hot water submersible pump
Geothermal well _ hot springs use hot water submersible pump to enhance the water, then most of the water quality of hot water wells have different degrees of corrosive and a small amount of sediment; simply spray paint in the unit table, and can not effectively prevent the pump body Corrosion of wear-resistant materials, the unit cost is relatively high, stainless steel material _ duplex steel _ copper material for hot water wells to enhance the application of water is not a lot, mainly should be For the price of the problem.
Now to share with you the Shanghai Wei Shanghai pump pump components introduced electrostatic coating the advantages of coating treatment:
① excellent chemical resistance.
② excellent corrosion resistance:
Electrostatic paint coating can withstand sewage and a variety of water treatment agents (some of which will also produce corrosion of stainless steel)
● Concentrated brine.
● Sewage: urea, ammonia, hydrocarbons, sodium acetate, fatty acid Moet.
● eliminate agent: nitrogen, nitrogen, ozone.
● oxidant: oxygen, from potassium permanganate.
● flocculants and softeners: ferric chloride, aluminum chloride, sulfate.
③ excellent wear resistance.
④ excellent impact resistance.
⑤ excellent resistance to bending.
⑥ excellent weathering performance.
⑦ excellent resistance to cavitation performance.
⑧ excellent edge of the enclosed performance.
Electrostatic paint coating processing advantages:
● easy to control powder adhesion;
● can achieve partial coating;
- the coating can be melted in an oven at a lower temperature and for a shorter period of time than the preheating step of the fluidized bed;
• No cross-linking risk compared to thermosetting materials;
● the required amount of powder is small;
● Coating automation can be achieved.
Electrostatic paint coating treatment is mainly used in hot water submersible pump body: the fluid flow shell on the impeller, the effective avoid some unnecessary wear and tear corrosion agent. Several years of application by the customer's unanimous approval
Now to share with you the Shanghai Wei Shanghai pump pump components introduced electrostatic coating the advantages of coating treatment:
① excellent chemical resistance.
② excellent corrosion resistance:
Electrostatic paint coating can withstand sewage and a variety of water treatment agents (some of which will also produce corrosion of stainless steel)
● Concentrated brine.
● Sewage: urea, ammonia, hydrocarbons, sodium acetate, fatty acid Moet.
● eliminate agent: nitrogen, nitrogen, ozone.
● oxidant: oxygen, from potassium permanganate.
● flocculants and softeners: ferric chloride, aluminum chloride, sulfate.
③ excellent wear resistance.
④ excellent impact resistance.
⑤ excellent resistance to bending.
⑥ excellent weathering performance.
⑦ excellent resistance to cavitation performance.
⑧ excellent edge of the enclosed performance.
Electrostatic paint coating processing advantages:
● easy to control powder adhesion;
● can achieve partial coating;
- the coating can be melted in an oven at a lower temperature and for a shorter period of time than the preheating step of the fluidized bed;
• No cross-linking risk compared to thermosetting materials;
● the required amount of powder is small;
● Coating automation can be achieved.
Electrostatic paint coating treatment is mainly used in hot water submersible pump body: the fluid flow shell on the impeller, the effective avoid some unnecessary wear and tear corrosion agent. Several years of application by the customer's unanimous approval
2017年1月11日星期三
订阅:
博文 (Atom)