2016年12月5日星期一

Main features of mine submersible pump

Main features of mine  submersible pump
1. The shell material of the Submersible pump, the way of introducing the cable, the electrical gap in the junction box, the distance between the electric clearance and the distance of the electric cable and the combination of the explosion of the screw thread are designed according to the regulations. 
2. Multistage pumps and motors are tightly combined into one common diving operation unit, has the characteristics of high head and large power, the lift can reach 100 ~ 1000m; and according to the change of the lift device, adjusting impeller and guide vane pump parts number, good interchangeability. 
 
3. Electric pump in the form of protection for the "IPx8", F grade insulation, allowing the motor temperature rise higher. 
 
4. Built-in motor can ensure that the electric pump even in the case of close to the row of dry suction tank in the long run, do not have to worry about the motor burned, can be achieved without management. 
 
5. Set high hardness guide bearing, control the radial swing of the rotor, to avoid the seal ring wear and pump efficiency decreased. 
 
6. Side inlet, water inlet can prevent large particles into the pump. 
 
7. The guide vane and volute chamber are symmetric multi outlet flow, can balance the radial force of pump off design conditions; the upper volute chamber is provided with a plurality of pressure relief hole, the upper part of the impeller pressure is reduced to the ambient pressure, the pressure due to the axial force distribution of pump in different accumulated almost perfectly balanced. 
 
8.Impeller back pressure is very high. Setting back blade, hand to prevent large particles of impurities of sewage directly into the sealing ring, a lower sealing ring at both ends of the pressure difference, reduce leakage. 
 
9.The lower part of the use of double row angular contact bearings, radial and axial force to withstand the multi stage Submersible pump at work; the upper part of deep groove bearings with dustproof cover. Large load margin to ensure the smooth running of the unit and long life. 
 
10. With flame retardant cable cable used in coal mine, the protection of spring installed in the end of the cable, a cable protection of large bending deformation, on the other hand can prevent the underground personnel directly pulling cable, the cable deformation makes the wiring cavity inlet. 
 
11. Motor shaft seal adopts two independent tandem mechanical seal, which can prevent the water into the oil chamber and prevent oil into the motor cavity. 
 
12. Impeller, guide vane and volute are not lower than the manufacturing material of ductile cast iron QT600-3, good abrasion resistance. 

2016年12月4日星期日

Applicable scope and advantages of stainless steel self - priming sewage pump

1.Stainless steel  sewage pump application:

Stainless steel self priming sewage pump applicable to chemical, petroleum, pharmaceutical, mining, paper, fiber, pulp, textile, food, power plant and municipal sewage works, public facilities, sewage pond aquaculture industry, it can be like a general water self-priming pump that does not need to install the valve, without irrigation water, and aspirate containing large particles of solid diameter exit diameter 60 and the fiber length is 1.5 times the diameter of the impeller dirt, sediment, mine waste contamination, waste treatment and sewage works all substance and colloid liquid. 

2.Stainless steel self suction sewage pump advantage:

1). Strong sewage capacity: special impeller anti blocking design, to ensure that the pump is efficient and no blockage. 
2). High efficiency and energy saving: the use of excellent hydraulic model, the efficiency than the general self priming pump 5 ~ 3. 
3). Self suction performance is good: self suction height than the general self priming pump 1 meters high, and self priming time is shorter. 

Features of corrosion resistance submersible sewage pump

Features of corrosion resistance submersible sewage pump :

1.The overall 304, 316 stainless steel precision casting, corrosion resistance, acid and alkali, no burr on the surface, no loopholes, smooth. 
 
2.The casting has a certain thickness, to ensure the service life of the pump. 
 
3.Built-in heat protector, when the motor temperature rise to 120 degrees Celsius, the protector will automatically cut off the power, in the case of a good water, 15-30 minutes later, the protector will start the pump to start working. 
 
4.Open impeller design, with good anti blocking, anti winding effect. 
 
5.Excellent corrosion resistant double mechanical seal, leak protection

2016年12月2日星期五

Structural principles and advantages of deep well pump

Two kinds of pumps are made of three parts. One is well on the part, which comprises a motor, a bearing box and a pump seat, used for supporting power, weight, nitric pump water diversion. Two is in the same transmission part, including the water delivery pipe, transmission shaft and bearing bracket, etc., from the transmission power and compliance. Three is the underground part, including the leaf Han, pump shell, Ye Hanzhou, etc., is the body of the pump, the water absorption, water extraction.  
The working principle of the deep well pump is basically the same as that of the general horizontal centrifugal pump. The power is driven by the driving shaft to drive the pump impeller to rotate, the vacuum is formed at the inlet of the impeller, and the well water is sucked. In order to reduce the energy loss of the water conveyance, the high speed water flow from the blade is eliminated by the flow guiding shell, and then flows along the water pipe to the farmland through the water head.  

Well pump has the following advantages:  

1. The  straw has the advantages of simple structure, the material and process requirements is not high, easy to manufacture.  
2. high efficiency.  
3. The engine installed in the wells, convenient installation.  
4. Leaves immersed in water, do not need to water before starting.  
5. The price is cheap.

The trouble and fix of deep well pump


The trouble and fix of deep well pump
Intermittent water or no water or less water:
Trouble:
1. Motor does not start (low voltage, wire too thin or too long, drop too much voltage does not start or pump stuck up)
2. Pipe blocked or Strainer blocked.
3.Pipe broken
4. Suction out of water
5. Submersible pump turn in the opposite
6. Impeller rings and seal rings worn
7. Impeller loose or blocked
8. Rotor shaft loose or broken rotor bar.
Fix:
1. Eliminate circuit fault, find out the cause and rule out seizure
2. Clear the blockage
3.Repair broken part
4. Decentralization of submersible pumps, if still no water coming out, the pump head may be more than the range head, recommended for pumps.
5. Swap any two connector cables
6. Change the new impeller, seal ring
7.Reinstallation new impeller clean block
8.Repair or change rotor