Axial flow pump performance adjustment methods are variable angle adjustment and variable speed adjustment of two, after we installed, if you do not meet the production requirements, you can use the following two ways to adjust the pump performance.
1, variable angle adjustment; from the structure point of view, axial flow pump impeller has a huge hub, easy to install adjustable angle of the blade. When the blade installation angle changes, the blade of the water lift also changed, thus changing the performance of the pump, which is the axial flow pump variable angle adjustment. As the blade mounting angle increases or becomes smaller, the flow rate of the axial flow pump, the head, the power changes, but the highest point of efficiency does not change, it is very advantageous to the axial pump performance adjustment.
2, variable speed adjustment; axial flow pump is working at a certain speed, and at a certain speed to obtain the appropriate flow, head, power and efficiency. When the speed changes, its performance parameters are also corresponding changes, so as to achieve the purpose of regulation. If the axial flow pump is powered by a diesel engine or a gasoline engine, it can change the size of the accelerator to change the speed. If the axial flow pump is connected with the power machine is a delta belt or flat belt indirect transmission device, you can change the transmission pulley diameter to change, Wheel or driven wheel can be, the purpose of foot to change the transmission ratio. Variable speed pump performance is more economical, wide range of applications, all agricultural pumps can be used.
2017年2月15日星期三
how to deal with mine submersible pump pump pipe fittings leakage
Daily use of mine submersible pumps in the process, we sometimes in the water pipe joints, connecting bolts, observed the phenomenon of leakage. The main reason: water pipe failure, defective, did not do the pressure test; installation of the pipeline process, the gasket is not put, the connector is not handled well, the coupling bolt is not even tightened. In response to these problems, we have to repair or even replace the defective pipes, tear off or re-arrange those centers that deviate from the larger butt joints. After aligning the hole, insert the coupling bolts into the tightening. After installing the complete piping, the pressure and the leakage test of the system are carried out.
In addition, due to mine submersible pump leakage will lead to insulation damage, bearing flooding, so that the unit to stop running, we should strengthen this precaution. The main reasons for the leakage of the pump include mechanical seal or cable inlet special seal, 0 type ring is damaged, power cable or signal cable is damaged; under normal circumstances, the protection device will promptly issued flooding, leakage, humidity and other alarm signals, Stop.
In order to avoid the phenomenon of pump leakage, before the installation, check the motor surface with or without water leakage phenomenon, and check the quality of the sealing parts; installation must ensure that the sealing parts of the end contact is good; check the motor before and check the insulation and grounding insulation resistance and Alarm system sensor components are intact. Found in the operation of water leakage, the need to remove the relevant seals and damaged cable, put on a new.
In addition, due to mine submersible pump leakage will lead to insulation damage, bearing flooding, so that the unit to stop running, we should strengthen this precaution. The main reasons for the leakage of the pump include mechanical seal or cable inlet special seal, 0 type ring is damaged, power cable or signal cable is damaged; under normal circumstances, the protection device will promptly issued flooding, leakage, humidity and other alarm signals, Stop.
In order to avoid the phenomenon of pump leakage, before the installation, check the motor surface with or without water leakage phenomenon, and check the quality of the sealing parts; installation must ensure that the sealing parts of the end contact is good; check the motor before and check the insulation and grounding insulation resistance and Alarm system sensor components are intact. Found in the operation of water leakage, the need to remove the relevant seals and damaged cable, put on a new.
Mine submersible pump shaft and bearing inspection and assembly
Under normal circumstances, the mine submersible pump journal can not have scars, journal cylindrical cylinder tolerance value of 0.0lmm; gear pump after a period of time, the maximum wear of the journal shall not be greater than 0.01D.
Mine submersible pump bearings generally use both rolling bearings and plain bearings, and sliding bearings for the form of copper sets. The use of rolling bearing gear pump bearing inner ring and the shaft with the H7 / js6; needle roller bearings without inner ring, the shaft and the needle with the H7 / h6; needle roller bearing outer ring and the cover with the K7 / H6, the use of sliding bearing mining pump bearing bore and cylindrical coaxial degree tolerance of 0. 01 mm; sliding bearing outer and end cover with R7 / h6;
Gear pump bearing wear should be replaced after the super-standard, rolling bearing assembly method and centrifugal pump rolling bearing assembly method is the same. With copper sleeve for the bearing gear pump, in the replacement of copper sets, the first should check the copper sleeve and the cover with the situation. In compliance with the requirements, the copper sleeve coated with oil, with a press to press it into the pump cover body, and finally in the bearing and end cap interface drilling thread with screws to fix it, to prevent copper sets Rotation or axial movement.
Copper sleeve assembly must be checked after the journal and copper sleeve with the gap, if the gap is too small, should be based on the journal, scraping copper sets, until meet the requirements so far. On the contrary, if the gap is too large to re-replace the copper sleeve.
Mine submersible pump bearings generally use both rolling bearings and plain bearings, and sliding bearings for the form of copper sets. The use of rolling bearing gear pump bearing inner ring and the shaft with the H7 / js6; needle roller bearings without inner ring, the shaft and the needle with the H7 / h6; needle roller bearing outer ring and the cover with the K7 / H6, the use of sliding bearing mining pump bearing bore and cylindrical coaxial degree tolerance of 0. 01 mm; sliding bearing outer and end cover with R7 / h6;
Gear pump bearing wear should be replaced after the super-standard, rolling bearing assembly method and centrifugal pump rolling bearing assembly method is the same. With copper sleeve for the bearing gear pump, in the replacement of copper sets, the first should check the copper sleeve and the cover with the situation. In compliance with the requirements, the copper sleeve coated with oil, with a press to press it into the pump cover body, and finally in the bearing and end cap interface drilling thread with screws to fix it, to prevent copper sets Rotation or axial movement.
Copper sleeve assembly must be checked after the journal and copper sleeve with the gap, if the gap is too small, should be based on the journal, scraping copper sets, until meet the requirements so far. On the contrary, if the gap is too large to re-replace the copper sleeve.
Stainless steel fountain pump vibration how to deal with?
Stainless steel fountain pump is the use of motor-driven centrifugal force to gradually introduce some of the liquid surface of the equipment, in the manufacture of fountains for people at the same time, but also for the surrounding environment to add a beautiful landscape. Stainless steel fountain pump selection is also a skill, improper selection and operation error is likely to cause vibration occurred Oh. So, what are the potential causes of fountain pump vibration is how to deal with it? Here we stainless steel fountain pump experts give some advice on the corresponding solution:
Two pumps in parallel should ensure that the pump performance is the same. Pump performance curve should be slow down type as well, can not have hump.
Regularly need to fill the oil bearing the appropriate amount of oil, for the long axis of liquid centrifugal pump, because the shaft there is a torsional vibration, if the use of a thrust tile, the damage is mainly thrust tile, then you can properly increase the viscosity of lubricating oil , To prevent the destruction of liquid dynamic pressure lubricating film.
Note: Eliminate the factors that lead to overloading the stainless steel fountain pump, such as the runner blockage; extend the pump's start time properly, reduce the disturbance to the drive shaft, reduce the collision and friction between the rotating parts and the stationary parts, The heat caused by the deformation; for water lubricated sliding bearings, start the process should be added pre-run water, to avoid dry start until the water pump and then stop the water.
Stainless steel fountain pump It is recommended to use the measurement and analysis vibration conditions to determine the optimum operating parameters of the pump in order to prevent the amplitude of the stainless steel fountain pump from being too large.
Two pumps in parallel should ensure that the pump performance is the same. Pump performance curve should be slow down type as well, can not have hump.
Regularly need to fill the oil bearing the appropriate amount of oil, for the long axis of liquid centrifugal pump, because the shaft there is a torsional vibration, if the use of a thrust tile, the damage is mainly thrust tile, then you can properly increase the viscosity of lubricating oil , To prevent the destruction of liquid dynamic pressure lubricating film.
Note: Eliminate the factors that lead to overloading the stainless steel fountain pump, such as the runner blockage; extend the pump's start time properly, reduce the disturbance to the drive shaft, reduce the collision and friction between the rotating parts and the stationary parts, The heat caused by the deformation; for water lubricated sliding bearings, start the process should be added pre-run water, to avoid dry start until the water pump and then stop the water.
Stainless steel fountain pump It is recommended to use the measurement and analysis vibration conditions to determine the optimum operating parameters of the pump in order to prevent the amplitude of the stainless steel fountain pump from being too large.
Fountain pump attention points during disassembly
Fountain pumps can be seen everywhere in our real life, a device that can go fountains and see the fountain pump in every part of the world. It's an important fountain pump to get a popular welcome The reason people use the fountain pump fountain to get happiness, the same use of fountain pump to relax their body and mind. Here to explain the fountain pump in the demolition of attention to points.
Check the fountain Submersible pump bearings: check the motor part of the upper and lower bearings, if found wear or clearance is too large, to be timely replacement of new bearings, is strictly prohibited "sick" improvised use.
Check the following:
If the motor is running, the submersible pump produces a "click" sound, and the cycle is proportional to the speed, and the hand when the rotor is laborious, bearing raceway is a bit astringent or avulsion phenomenon; if the bearing issued intermittent " Choked choked "sound, the rotor when the rotor is uncertain when the dead point, the general is a submersible pump ball frame damage, broken inner ring or broken ball. Encountered the above situation, you must replace the bearings, so as to avoid greater damage.
Submersible pump should be marked before the front and rear cover and the base of the seat. In order to repair the assembly by the original assembly, it will not cause the assembly error caused by the shaft is different from the heart; in the demolition submersible pump impeller and sleeve and other components, it should be noted that do not hard hard punch, the principle of thermal expansion, Edge tapping or "Rama" and other tools to remove.
Check the fountain Submersible pump bearings: check the motor part of the upper and lower bearings, if found wear or clearance is too large, to be timely replacement of new bearings, is strictly prohibited "sick" improvised use.
Check the following:
If the motor is running, the submersible pump produces a "click" sound, and the cycle is proportional to the speed, and the hand when the rotor is laborious, bearing raceway is a bit astringent or avulsion phenomenon; if the bearing issued intermittent " Choked choked "sound, the rotor when the rotor is uncertain when the dead point, the general is a submersible pump ball frame damage, broken inner ring or broken ball. Encountered the above situation, you must replace the bearings, so as to avoid greater damage.
Submersible pump should be marked before the front and rear cover and the base of the seat. In order to repair the assembly by the original assembly, it will not cause the assembly error caused by the shaft is different from the heart; in the demolition submersible pump impeller and sleeve and other components, it should be noted that do not hard hard punch, the principle of thermal expansion, Edge tapping or "Rama" and other tools to remove.
How to improve the running life of hot water submersible pumps
How to improve the running life of hot water submersible pumps
(1), hot water submersible pump population piping should be sealed well, hot water submersible pumps generally have good self-absorption performance, in the course of work, the population pressure to negative pressure, bad seal leading to air into, Resulting in increased noise vibration of the pump, damage to the pump rotor parts, hot water submersible pump life.
(2), hot water submersible pump at the beginning of the start, no pressure in the export formation, do not blindly speed to prevent shaft or bearing premature damage.
(3), hot water submersible pump outlet pressure measurement points to set up interlock to stop the alarm, otherwise, once the discharge pipe blocked, easy to cause the pump body is bad.
(4), for high viscosity hot water submersible pumps, easy to crystal pump, in the system should be set up Tt parking cleaning system, so that after the pump will be easy to clear the pump outside the pump, to prevent the crystallization in the pump, start up.
(5), cleaning pipetting, do not use hot water submersible pump pump delivery cleaning fluid, should remove the inner parts, after the end of the installation of fluid, so as not to pump inside the stick foreign body.
(6), for high temperature submersible pumps, because the pump at high temperature operation, the temperature will be shifted after the transfer, so the installation of the cold pipe should be set on the hinge seat, which can effectively prevent the temperature after the pipe displacement.
(7), for high temperature submersible pumps, couplings must be hot after the pump heat correction, in order to avoid additional torque caused by operation.
(8), the pump heat medium jacket temperature should be slightly lower than the front and rear jacket tube heat medium temperature. Because the melt viscosity and shear rate into a decreasing function, the gear squeeze, bearing the shear will melt temperature through the pump after the rise of 3 ℃ -5 ℃, reduce the heat medium temperature to prevent melt degradation.
(9), speed to slow, do not make the sharp rise in pressure before and after, so as not to damage the bearing or make the melt plugging lubrication ring Road.
(10), hot water submersible pump outlet filter to be replaced regularly, so as not to plug the outlet. The pump long-term operation under high pressure.
(11), should be replaced regularly. When the hot water submersible pump due to the bearing gap becomes larger and larger when the voice should be replaced. Of course, the bearings can be re-used to re-use the bearing after alloying.
(1), hot water submersible pump population piping should be sealed well, hot water submersible pumps generally have good self-absorption performance, in the course of work, the population pressure to negative pressure, bad seal leading to air into, Resulting in increased noise vibration of the pump, damage to the pump rotor parts, hot water submersible pump life.
(2), hot water submersible pump at the beginning of the start, no pressure in the export formation, do not blindly speed to prevent shaft or bearing premature damage.
(3), hot water submersible pump outlet pressure measurement points to set up interlock to stop the alarm, otherwise, once the discharge pipe blocked, easy to cause the pump body is bad.
(4), for high viscosity hot water submersible pumps, easy to crystal pump, in the system should be set up Tt parking cleaning system, so that after the pump will be easy to clear the pump outside the pump, to prevent the crystallization in the pump, start up.
(5), cleaning pipetting, do not use hot water submersible pump pump delivery cleaning fluid, should remove the inner parts, after the end of the installation of fluid, so as not to pump inside the stick foreign body.
(6), for high temperature submersible pumps, because the pump at high temperature operation, the temperature will be shifted after the transfer, so the installation of the cold pipe should be set on the hinge seat, which can effectively prevent the temperature after the pipe displacement.
(7), for high temperature submersible pumps, couplings must be hot after the pump heat correction, in order to avoid additional torque caused by operation.
(8), the pump heat medium jacket temperature should be slightly lower than the front and rear jacket tube heat medium temperature. Because the melt viscosity and shear rate into a decreasing function, the gear squeeze, bearing the shear will melt temperature through the pump after the rise of 3 ℃ -5 ℃, reduce the heat medium temperature to prevent melt degradation.
(9), speed to slow, do not make the sharp rise in pressure before and after, so as not to damage the bearing or make the melt plugging lubrication ring Road.
(10), hot water submersible pump outlet filter to be replaced regularly, so as not to plug the outlet. The pump long-term operation under high pressure.
(11), should be replaced regularly. When the hot water submersible pump due to the bearing gap becomes larger and larger when the voice should be replaced. Of course, the bearings can be re-used to re-use the bearing after alloying.
Hot water submersible pump installation method?
Hot water submersible pump installation method?
(1) According to the hot water submersible pump spindle position can be divided into:
① vertical installation: (vertical) pump installed in the vertical direction of the spindle, the installation of the bracket. The vertical installation of the pump is limited by the working environment of the pump (eg piping pumps, submerged pumps, deep well pumps, drum pumps, hot water submersible pumps), installation space constraints (vertical marine pumps) and design factors (eg vertical high speed Pump).
② Horizontal installation: The horizontal (horizontal) submersible pump installed in the horizontal direction of the spindle, the installation of the bracket, which is the installation of most pumps.
(2) by hot water submersible pump can be divided into:
① wet installation: the pump part or all installed in the liquid installation. This installation is compact, small footprint, installed directly in the sewage pool, no need to build a dedicated pump room to install pumps and motors, you can save a lot of land and infrastructure costs, easy installation and maintenance; but the pump seal Performance, insulation performance requirements.
② dry installation: the pump completely placed outside the installation of the liquid, which is the installation of most of the pump, with intuitive maintenance, size is appropriate, the lower requirements of the motor pump, the characteristics of strong adaptability.
(3) According to whether the submersible pump can be divided into:
① mobile installation: the pump or its components installed on a removable carrier (such as car) installation method. This installation method used in small, intermittent use, the use of more occasions.
② fixed installation: the pump fixed to the foundation or bracket on the installation, is the most commonly used installation.
(1) According to the hot water submersible pump spindle position can be divided into:
① vertical installation: (vertical) pump installed in the vertical direction of the spindle, the installation of the bracket. The vertical installation of the pump is limited by the working environment of the pump (eg piping pumps, submerged pumps, deep well pumps, drum pumps, hot water submersible pumps), installation space constraints (vertical marine pumps) and design factors (eg vertical high speed Pump).
② Horizontal installation: The horizontal (horizontal) submersible pump installed in the horizontal direction of the spindle, the installation of the bracket, which is the installation of most pumps.
(2) by hot water submersible pump can be divided into:
① wet installation: the pump part or all installed in the liquid installation. This installation is compact, small footprint, installed directly in the sewage pool, no need to build a dedicated pump room to install pumps and motors, you can save a lot of land and infrastructure costs, easy installation and maintenance; but the pump seal Performance, insulation performance requirements.
② dry installation: the pump completely placed outside the installation of the liquid, which is the installation of most of the pump, with intuitive maintenance, size is appropriate, the lower requirements of the motor pump, the characteristics of strong adaptability.
(3) According to whether the submersible pump can be divided into:
① mobile installation: the pump or its components installed on a removable carrier (such as car) installation method. This installation method used in small, intermittent use, the use of more occasions.
② fixed installation: the pump fixed to the foundation or bracket on the installation, is the most commonly used installation.
订阅:
博文 (Atom)