Fountain pump in the course of the operation will be interrupted water failure, the failure of several common analysis to you as a reference:
First, the motor does not start, remove the circuit failure;
Second, the pipeline rupture, welding or replacement of new pipe;
Third, the pipeline blockage, removal of obstructions;
Fourth, the water exposed surface, if the discharge pump is still ineffective, the proposed change pump;
Fifth, the water network blockage, remove the blockage;
Sixth, pump seal ring, impeller damage, replace the new pieces;
7, pump reversal, replace the power cord phase sequence.
Also to remind you to check the fountain pump motor, if found under the cracks, rubber seal ring damage or failure, should be replaced or repaired in order to prevent water infiltration machine
2017年2月8日星期三
Fountain pump principle and the use of precautions
Fountain pump principle and the use of precautions
Fountain pump burnout or winding insulation damage will be leakage, very dangerous, in the case of electricity not to touch the fountain pump and pipes, etc., to prevent electric shock, should immediately cut off the power, and then processed.
First, the fountain pump dehydration operation, cooling deterioration, should increase the water level or reduce the fountain pump installation position.
Second, the power supply voltage is too low, should adjust the transformer voltage.
Third, the fountain pump motor winding turns, phase or short circuit to the ground, should be overhauled, replace the winding.
Fourth, the power cable pressure drop is too large, should be replaced by freshman specifications of the cable.
Fifth, the fountain pump starts too often, it should be in accordance with the instructions required to operate.
6, pump impeller stuck, should promptly check the impeller, clear impeller debris.
Seven, fountain pump inlet blockage, should promptly clean up the entrance debris and add filter.
Fountain pump burnout or winding insulation damage will be leakage, very dangerous, in the case of electricity not to touch the fountain pump and pipes, etc., to prevent electric shock, should immediately cut off the power, and then processed.
First, the fountain pump dehydration operation, cooling deterioration, should increase the water level or reduce the fountain pump installation position.
Second, the power supply voltage is too low, should adjust the transformer voltage.
Third, the fountain pump motor winding turns, phase or short circuit to the ground, should be overhauled, replace the winding.
Fourth, the power cable pressure drop is too large, should be replaced by freshman specifications of the cable.
Fifth, the fountain pump starts too often, it should be in accordance with the instructions required to operate.
6, pump impeller stuck, should promptly check the impeller, clear impeller debris.
Seven, fountain pump inlet blockage, should promptly clean up the entrance debris and add filter.
Submersible pump supporting cable requirements
Submersible pump installation cable to overhead, the power cord should not be too long, the cable into the water pipe flange groove. If the power supply and the distance between the use of water pumps, wiring cable cross-sectional area should be increased, the joints should be minimized in order to reduce line pressure drop. 10kW submersible pumps can be started directly below the control device is best to use automatic air circuit breaker, without such electrical appliances, deep well submersible pumps. Switched switches may also be used, provided that suitable fuses are installed in accordance with the operating current of the submersible pump. 10kW or more submersible pumps should be equipped with buck starting cabinet.
The safe operation of the submersible pump cable into the flange of the water pipe flange, and with water-resistant rope tied to the cable fixed to the water pipe. Do not subject the cable to stress when the submersible pump is under water or water, to prevent the power cord from breaking, and to prevent abrasion in the course of the cable going down.
The safe operation of the submersible pump cable into the flange of the water pipe flange, and with water-resistant rope tied to the cable fixed to the water pipe. Do not subject the cable to stress when the submersible pump is under water or water, to prevent the power cord from breaking, and to prevent abrasion in the course of the cable going down.
2017年2月7日星期二
Caused by several factors of the submersible pump burned
Some users in the process of using the submersible pump due to improper operation caused by water pump burned, Shanghai Wei Shanghai Pump Co., Ltd. engineering and technical personnel to analyze several factors for your reference:
1, flow and head. Such as the choice of the lift is too high, but easy to burn the motor, be careful not to reverse the water when the reverse small, large current, the reverse will damage the motor windings.
2, the installation of submersible pumps, submersible pumps do not sink into the mud, otherwise it will lead to poor heat and burn the motor winding.
3, try to avoid low-voltage boot.
4, do not allow long-term overload pump operation, do not smoke a large amount of sediment water, dehydration pump running time should not be too long, so as to avoid overheating and burning the motor. During operation, the operator must observe whether the operating voltage and current are within the value specified on the nameplate. If not, the operator should stop the motor, find the cause and rectify the fault.
5, some submersible pumps in the sealed room to add lubricating oil, or mechanical seals easily damaged, the motor is easy to burn due to water.
1, flow and head. Such as the choice of the lift is too high, but easy to burn the motor, be careful not to reverse the water when the reverse small, large current, the reverse will damage the motor windings.
2, the installation of submersible pumps, submersible pumps do not sink into the mud, otherwise it will lead to poor heat and burn the motor winding.
3, try to avoid low-voltage boot.
4, do not allow long-term overload pump operation, do not smoke a large amount of sediment water, dehydration pump running time should not be too long, so as to avoid overheating and burning the motor. During operation, the operator must observe whether the operating voltage and current are within the value specified on the nameplate. If not, the operator should stop the motor, find the cause and rectify the fault.
5, some submersible pumps in the sealed room to add lubricating oil, or mechanical seals easily damaged, the motor is easy to burn due to water.
Causes of Deep Well Pump Stuck and Its Solution.
Causes of Deep Well Pump Stuck and Its Solution.
There are two main reasons why deep well pump can jam:
1, the wall of the falling objects stuck, you pull look at the pump at every turn, a little fixed sedimentation is certainly buried in the water pump, so we should use things hard pull up, pull like a drop of stuck , The pump is active, you pull back and forth to pull back the pump, the falling objects broken, usually vulgar stone stubble, not stone, stone is not broken, generally do not fall down, so you can pull up the pump.
2, is the well face when the rock face and slag, after a year of precipitation, the pump buried, and may be buried in the filter part, not Sheung Shui. In addition, the new installation of deep well pump to 1-2 months to move, to prevent sediment buried in the pump.
There are two main reasons why deep well pump can jam:
1, the wall of the falling objects stuck, you pull look at the pump at every turn, a little fixed sedimentation is certainly buried in the water pump, so we should use things hard pull up, pull like a drop of stuck , The pump is active, you pull back and forth to pull back the pump, the falling objects broken, usually vulgar stone stubble, not stone, stone is not broken, generally do not fall down, so you can pull up the pump.
2, is the well face when the rock face and slag, after a year of precipitation, the pump buried, and may be buried in the filter part, not Sheung Shui. In addition, the new installation of deep well pump to 1-2 months to move, to prevent sediment buried in the pump.
Under what circumstances should the deep well pump shut down
The deep well pump should immediately stop operation in one of the following situations:
First, the rated voltage when the current exceeds the rated value;
Second, the rated head, the flow lower than normal under normal circumstances;
Third, the insulation resistance of less than 0.5 megohm;
4, move the water level down to the pump suction inlet;
5, when the electrical equipment and circuit irregularities;
Sixth, the pump has a sudden sound or greater vibration;
7, protection switching frequency trip.
First, the rated voltage when the current exceeds the rated value;
Second, the rated head, the flow lower than normal under normal circumstances;
Third, the insulation resistance of less than 0.5 megohm;
4, move the water level down to the pump suction inlet;
5, when the electrical equipment and circuit irregularities;
Sixth, the pump has a sudden sound or greater vibration;
7, protection switching frequency trip.
Small submersible pump voltage is too low
Small submersible pump is widely used in our daily life, the following voltage is too low, the small submersible pump how to use the correct, Zhengzhou Nine Dragons pump technical staff will give you a reasonable proposal:
As the power supply voltage is too low cause a small submersible pump can not start, the need to adjust the power supply voltage to 342V or more. In the disaster emergency drainage must use a small submersible pump, if the voltage is lower than 342v, you can take temporary and measures: appropriate to adjust the large pump protection switch setting current, so that the use of small submersible pump, the protection switch will not Frequent tripping due to overload. But should be used to control the submersible pump stator winding current does not exceed 1.1 times its rated current, and control the use of time, so that small submersible pump will not be used for too long, overload too long, resulting in stator winding temperature rise too high overheating damage.
As the power supply voltage is too low cause a small submersible pump can not start, the need to adjust the power supply voltage to 342V or more. In the disaster emergency drainage must use a small submersible pump, if the voltage is lower than 342v, you can take temporary and measures: appropriate to adjust the large pump protection switch setting current, so that the use of small submersible pump, the protection switch will not Frequent tripping due to overload. But should be used to control the submersible pump stator winding current does not exceed 1.1 times its rated current, and control the use of time, so that small submersible pump will not be used for too long, overload too long, resulting in stator winding temperature rise too high overheating damage.
订阅:
博文 (Atom)