2017年2月4日星期六

Introduction of Mine Submersible Pump

Introduction of Mine Submersible Pump
1, the use of mining submersible pump:
Mine submersible pump is mainly used for the central pump drainage of coal mines, coal mines by flooding after the emergency drainage or mine drainage. Due to the small diameter, light weight, have a wider range of use.
2, mining submersible pump model:
Mine submersible pumps are commonly used centrifugal pumps. Centrifugal water pump is a working turbine, mining submersible pumps are commonly used in d-type, da-type and tsw-type multi-stage centrifugal pumps; and the bottom of the water nest and mining areas are commonly used drainage b-type, ba-type and bz Type single-stage centrifugal pumps.
3, mining submersible pump performance parameters:
Mine submersible pump main performance parameters for speed; flow; allow inhalation of the vacuum height; shaft power; gas turbidity margin; efficiency;
4, mining submersible pump features:
A, motor and pump body can sneak into the water, safe and reliable operation.
B, mine submersible pump on the well pipe and the water pipe does not have special requirements.
C, mining submersible pump simple structure, raw materials than the province.
D, mining submersible pump small size, small footprint.
E, mining submersible pump easy to install, do not need to build a special pump, the use and maintenance is simple.

2017年2月3日星期五

Reason of Decreasing Insulation Resistance of Stator Winding of Motor in Deep Well Pump

Deep well pump motor stator winding insulation resistance decline reasons:
    The insulation resistance of the stator windings of the submersible motor is related to the leakage of the mechanical seal of the shaft end of the motor, the seal leakage of the motor base and the end cover, and the insulation of the motor stator winding.
    (1) damage or damage to the stator winding treatment method is to check the damage or damage to the stator winding, repair damaged or damaged winding, and re-diving motor stator windings dry, improve the stator winding insulation resistance.
    (2) oil-filled motor oil after the poor water, the oil capsule is not tightly sealed at both ends or oil bag rupture treatment method is to reload or replace the oil capsule, replace the insulating oil. If the insulation resistance of the stator winding is lower than the specified value, re-dry the stator winding.
    (3) The static sealing leakage of the joints between the frame and the end cover is to re-install or replace the seal O-ring of the joint between the base and the end cover and re-dry the stator windings of the submersible motor Processing, improve the motor stator winding insulation resistance.
    (4) motor shaft end of the mechanical seal leakage treatment method is to motor shaft extension of the mechanical seal repair or re-assembly or replacement of the new mechanical seal and re-motor stator windings dry treatment to improve the stator winding insulation resistance.
    (5) cable connector water treatment is to re-bandaged cable connector, and re-motor stator windings for drying, improve the stator winding insulation resistance.

Measuring Method and Precautions of the Winding of Motor in Deep Well Pump

Measuring Method of Motor Winding of Deep Well Pump and Its Matters Needing Attention
    When measuring the DC resistance of the stator windings of a deep well pump, the temperature inside the motor of the deep well pump should be in accordance with the ambient medium temperature, and the rotor of the submersible pump should be stationary. The DC resistance of the stator winding shall be measured at the end of the lead-out cable of the submersible pump.
     For three-phase submersible deep-well pumps, the DC resistance of each phase winding or the DC resistance of each line should be measured. For single-phase submersible pumps, the DC resistance of the main winding and the secondary winding should be separately measured.
When the resistance value of the deep-well pump pump stator winding is large (more than 1Ω), it is generally measured by single-arm bridge. When the resistance value of the deep well pump stator winding is less than 1Ω, because the contact resistance and the wiring resistance exist, if still using the single-arm bridge to measure, will have a greater impact on the measured resistance value of cattle, Arm bridge for measurement.

Buy QJ deep well submersible pumps do not have to pursue high lift

Buy QJ deep well submersible pumps do not have to pursue high lift
   In the sales of submersible pumps, often encounter some customers how to choose the pump, in addition to some of the common sense we know, a large part of the customers prefer the selected head higher than the actual use of lift, that this will be more insurance , Will be foolproof, in fact, this is not only unnecessary, and may cause damage to the pump. Here I come to explain to you the disadvantages of doing so.
 1, Shanghai Weihu pump produced by the deep well submersible pump will not virtual standard to 175QJ10-100, for example, flow in the rated flow of 10 square cases, the lift can certainly reach 150 meters 1 meter will not be less. There are many users afraid of the way up to the nameplate of the standard way, here, please rest assured. Now there are indeed many South manufacturers in pursuit of profit virtual standard, disrupt the market order, QJ submersible pump is not the case.
2, the actual use of head and rated head too much difference, will cause the motor overload, which may cause the motor cable package burned. For example, customers want to show the pump to play 80 meters, in fact, choose the pump 200QJ40-78 on it, the result is selected 200QJ40-117, in which case the lift is much smaller than the rated head, it will cause the motor overload, that is, We commonly known as the "suffocation pump", causing the motor burned, more harm than good.
 3, the selected submersible pump in the same flow conditions, the higher the higher the motor, the greater the power consumption. Or give the example above, 200QJ40-78 submersible pump is equipped with a 15KW motor, 200QJ40-117 with a 22KW motor, the greater the cost of higher motor. So the election submersible pump, then the best fit, no need to choose too much, resulting in unnecessary losses.

Development history of submersible pump in the world

Development history of submersible pump in the world
   Submersible pump is a pump and motor combined into a special transport of liquid machinery, as the name suggests, mechanical and electrical integration into the water work. Its structure is simple, easy to use. With the development of material science, sealing technology, control and protection technology and the improvement of hot and cold processing technology, submersible pump has been developing rapidly.
    In 1904, the United States Byron Jackson (Byron Jackson) the first company to successfully design, manufacture a horizontal connection of the submersible pump and submersible motor, which is the modern submersible pump "ancestors." In 1928, the company invented the direct connection of the vertical submersible pump, which is the modern form of deep well submersible pump. Visible, the development of submersible pump has been 60 years of history.
    Sweden's Flygt (Sterbery Flygt), the first successful development in 1948 the world's first water supply and drainage with a shallow (or operating surface) submersible pump, fundamentally simplifies the pump type, the reform of the building foundation pit And mine drainage equipment, and soon in the world-wide success. In 1956, Flygt produced submersible pumps for sewage, which reduced the cost of sewage pumping stations by about half. In addition, Flygt has also solved a series of difficult problems, the development of a variety of special submersible pumps can be used to suck the abrasive liquid containing solid particles, viscous solution and corrosive liquids. In recent years, Flygt company in pump structure has made great progress, and the development of four series: pumping small particles containing abrasive liquid 2000 series, pumping civil and industrial wastewater 3000 series of large flow sewage submersible pump, pumping water Of the 5000 series, with a large flow of medium-lift screw (axial) type 7000 series.

Constant pressure water supply equipment supporting submersible pump installation

Constant pressure water supply equipment supporting submersible pump installation
1. There are three sets of submersible pumps in this cabinet, the power of submersible pump is 18.5KW. Can be manually or automatically switch from SA1 (hand automatically switch) for manual or automatic control switch. When the manual function is selected, the automatic operation of the controller is stopped. The manual indicator lights. Manual start button SB1, No. 1 submersible pump starts, press the button SB2, the No. 1 submersible pump stop. Start up the motor for a short time during commissioning and check that the steering of the submersible pump motor is correct. Manual start button SB3, No. 2 submersible pump start, press the button SB4, the two dive pump stop. Debugging the same to check the pump motor steering is correct. No. 3 submersible pumps and so on. When automatic control is selected, the controller will automatically adjust the controller according to the external pressure. When the SA1 (manual automatic switch) is selected, the inverter will switch the frequency and pump frequency. When the external pressure continues to be less than the preset lower limit, the controller will switch the working frequency pump to work frequency, the next standby pump will enter the frequency conversion operation and maintain the pipeline pressure to the set value.
In the automatic state, when the external pressure continues to be greater than the set upper limit to a preset time. The controller will cut off the first work-frequency pump. Until the pipe pressure reaches the setting range. When the external protection function is connected, if the tank water level is lower than the set minimum water level, or when the pipeline pressure exceeds the allowable value, the pump will be shut down and restarted after reaching the starting condition. The above protection can also be installed according to site conditions.
2. Industrial frequency conversion design. Does not change the power frequency loop. Dual standby, redundant control to meet the application of various operating conditions.
3. Need to install a pressure sensor, the range is 0-1MP (0-10KG)
4. The main circuit cable shall be provided by the purchaser.

Deep well pump supporting cable is what material

Deep well pump supporting cable is what material
    Rubber cable is a multi-strand thin copper wire as a conductor, outsourcing rubber insulation and rubber sheath of a soft and removable cable varieties.Generally speaking, including general rubber flexible cable, welding machine cable, submersible motor cable, Radio cable and photographic light source cable and other varieties.
Waterproof rubber sleeve cable and deep well pump cable, mainly used for submersible motor matching. Model JHS, JHSB
Use a dedicated submersible pump cable connector
The sealing device of the submersible pump cable joint relates to the sealing device of the pump, the cable connector is provided in the terminal box, the compression nut is arranged on the cable connector, the expansion sealing gasket is arranged between the cable connector and the compression nut, There is an expansion sealing gasket between the wire joint and the compression nut. The compression nut is not in direct contact with the cable connector, and the compression nut can not scratch and wear the cable connector during assembly, and the sealing effect is good, suitable for all kinds of deep well pump Cable connector.