2017年1月17日星期二

Fountain pump use range

Fountain pump range of use, due to the different types of products, different types of use is also a strict requirement. details as follows:
Rotate by hand to see whether the pump is flexible rotation, check the pump piping and joints for loosening or leakage phenomenon.
Check the oil in the bearing body to ensure that the oil level in the oil near the center line and, as the case in time to replace or supplement.
Check whether the damaged pump cable and power supply, electrical equipment is reliable, power supply voltage, frequency, and nameplate requirements are consistent, the deviation is within the allowable conditions within the scope of use.
After installation, should be taken to start the motor, try to see whether the motor steering is correct. After each shutdown and before starting, must be measured in the hot and cold insulation resistance to observe the insulation resistance changes.
In the first month of work, after 100 hours of work, the oil should be replaced, after each 1000 hours oil change. On the water-filled need to regularly replace the upper and lower end caps, bearing room skeleton oil seal and lithium-based grease to ensure good lubrication.
Regularly check the sleeve wear, when there is greater wear, should be replaced in time.
Shanghai fountain submersible pump used in the winter season, after parking, the pump must be the lower part of the water plug screwed open, and the media put the net to prevent the pump frost. Long-term disabled, can not be allowed to soak in water. The rotating parts and joints coated with grease installed, stored upright at room temperature, dry, non-corrosive chemicals where the proper custody.

The advantages of stainless steel fountain pump

Stainless steel fountain pump advantage of our customers in the procurement of pumps will consult our stainless steel pump What are the benefits, of course, this advantage is relative to the cast iron pump, our cast iron pump is cast iron processing, with products The use of the process easier to rust, then the stainless steel pump is used in the international standard 304 stainless steel materials, so the process will not rust in the use of the situation. Effectively guarantee the use of life, there is the difference between the motor, stainless steel motor can be equipped with the corresponding inverter, the effective guarantee of some musical fountain, program-controlled fountain use, the use of a wider range.
Almost can be done is a maintenance-free use of the process, so when you purchase the fountain pump, if the budget is reasonable or select the stainless steel must be easy to use, so you use them easy to use, Save a lot of trouble

304 stainless steel fountain pump description

304 stainless steel fountain pump description

The Use of Small Power Fountain Pump

The Use of Small Power Fountain Pump

2017年1月16日星期一

Analysis of fountain pump failure

Fountain pump failure analysis, fountain pump, fountain pump flow is insufficient, the occurrence of cavitation, etc. are hydraulic failure. Pump does not run, overheating of the bearing is a mechanical failure. Under normal circumstances, the two faults exist in a phenomenon, such as the lack of head, pump Diao deep operation there is no abnormal vibration and sound.
Troubleshooting should follow the following principles: with the fault should be promptly excluded, the machine can not make sick work. Troubleshooting should: clarify the performance, analysis of a reason to be eliminated. The cause of the failure should be analyzed in many ways, and strive to accurately determine. Exclusion of specific conditions should be specific treatment, can not be mechanically applied.
Analysis and Solution of Common Fault
1) the pump does not water, usually due to a impeller flow path blocked by debris, 2 pump impeller reverse direction of operation, 3 device head beyond the pump design head range caused. As long as the clean-up impeller flow channel, re-connect the motor power cord and re-select the appropriate pump can solve the problem.
4) bending deformation of the pump shaft. With the dial gauge to measure the o axis of the pump shaft in the radial volume, if it is rolling bearings, usually should not be more than 0.05mm beating, if it is sliding bearings, sliding bearing friction should not exceed the gap. In addition, check the rotation of the shaft and wheel rotation Yi, pump normal operation, at different speeds have different rotation jitter allowed value, usually 1450 r / min allowable value of not more than 0.15mm, 2900 points in time to allow The value is less than or equal to 0.10 mm. If the permissible value is exceeded, the shaft and wheel v are measured circumferentially point by point to see if the wheel 0 is eccentric, or is not concentric, or the shaft is bent. It is also possible that the axis is good for neutrality, the rotation is very large, or there is no rotation Mm, but the pay neutral is poor, should be corrected.
5) There is abnormal vibration and sound when the pump is running. It is usually caused by the poor neutral of pump shaft and motor shaft, bending deformation of pump shaft, cavitation of running and friction of rotating parts. If none of the above problems exists, Feet, pump shell bolts without loosening, check the pump pipe there is a clear stress. If the stress is too great, it should be supported at the inlet or outlet to reduce or eliminate stress. Remove and reinstall if necessary.
2) Lack of head, pump outlet pressure can not meet the needs of working conditions. There are many reasons for this failure: pump cavitation, impeller wear and tear after long-term use, supporting the motor speed is lower than the required pump speed, etc., will lead to lower pump head. Increase the level of the pump inlet level or Yang lk pump installation location, can avoid the occurrence of cavitation. Replacement of the impeller is worn, and select the pump to match the motor, is one of the ways to troubleshoot.
3) bearing overheating, bearing more than the normal temperature range. Generally due to a bearing housing lack of oil or 2 oil deterioration caused by bearing temperature anomalies. In the timely confirmation of the reasons to add grease, update the lubricating oil, so as not to damage the bearings. Second, the cause of bearing overheating and 3 pump shaft, motor shaft is not concentric,

2017年1月15日星期日

Hot water well submersible pump unique structural features

1, hot water well submersible pump heat resistant high temperature submersible motor unique structure
    The high-temperature motor is filled with water and sealed structure, the cavity is filled with water or rust-proof lubricating fluid (rust inhibitor). The joints are sealed with 0-shaped rubber seals or sealant. The shaft end of the motor is equipped with a rubber skeleton oil seal 4 or a single-face mechanical seal 5 so as to prevent the solid impurities and sediment particles in the motor from entering the motor interior. The stator (including windings) 7 of the motor, the rotor 8 and the bearings are all operated in water. The stator winding of the motor is made of water-resistant winding wire with polyethylene insulation, polyethylene insulation or modified polypropylene insulation, and has good water-proof insulation performance and long service life. Water lubricated sliding guide bearings 6 and 9 made of copper alloy, graphite or polymer plastic and the like are attached to the upper and lower portions of the motor, and a water lubricated thrust bearing 11 made of graphite or thermosetting plastic or the like is provided at the lower end of the shaft, In order to withstand the rotor running motor and the axial thrust of the pump. In order to limit the pump to start up the shaft to move up, resulting in short-term motor shaft seal sealing leakage, the lower part of the motor with thrust bearing sliding bearings 10. The bottom of the motor is equipped with rubber pressure regulating bladder 13, to adjust the cavity filled with water due to temperature or pressure changes caused by volume changes. For the thin steel coil shell structure, the shaft end of the installation of rubber skeleton oil seal or mechanical seal for power smaller, shorter core, the chassis force smaller motor. For the steel pipe shell structure, the overall rigidity is better for larger power, longer core, the chassis force larger motor.
2, hot water well submersible pump motor main features
    (1) wells with water-filled hot water submersible motor structure is simple, stator and rotor windings and core immersed in water, cooling effect, the output power, high efficiency.
    (2) due to water-filled high-temperature motor cavity filled with water, the use of the process of leakage on the installation of the well water quality will not produce pollution.
    (3) water-filled high-temperature motor stator windings, iron and bearings are working in the water, the stator winding wire used and its processing technology, joint materials and dressing process, water lubrication bearing structure, materials and processing technology, Iron and metal materials, anti-rust anti-corrosion treatment have high requirements.
    (4) water-filled motor has sufficient reliability, is the well with hot water submersible motors in the production of the most, the most widely used one.

2017年1月12日星期四

Identification of quality problems of hot water submersible pump several cases

Case 1:
  Due to failure to install according to the instructions required to fill the clean water and clean liquid, or did not put the steam hole open, resulting in false water level. Resulting in hot water submersible pump motor winding burned by the responsibility of the use or installation unit to be responsible.
  The phenomenon is: water invaded the location of the winding adhesion to one (the degree of adhesion can not help the same)
Case 2:
  Because the unit long-term unattended, there is no periodic clean wipe repair the circuit nodes, resulting in increased resistance wire blown fuse, protective measures to adjust and inappropriate or relay failure, resulting in phase loss, the responsibility of the burned winding by the user.
  Phenomenon: a hot water submersible pump unit can not start work, the motor insulation is zero. (If the motor power is large, the scene does not have to open the conditions, must return to the factory identification, the user can be assigned to participate in the identification of technical staff) Winding connection If there is a delta connection of which a winding Burned, the stars connected to the two-phase winding burned, which can be identified as lack of burned. Responsibility for this situation by the use of units to be responsible.
Case 3:
  The user according to the "instructions" requirements, in the one-year warranty period, after the open is due to mechanical wear and tear caused by motor damage, but because of the user's protective measures are sensitive, winding does not burn can continue to use, the factory is responsible for free maintenance Or replacement of mechanical parts, if the hot water submersible pump motor failure caused by mechanical failure of the winding, the user's protective measures do not work, the factory responsible for the maintenance but the cost of the burden of half of the maintenance.
Case 4:
  Hot water submersible pump motor rotor Broken shaft: rotor shaft and rotor silicon steel from: stator casing welding cracking: motor fastening screws loose, are manufacturing quality problems, the responsibility of the mountain manufacturer is responsible for. The solution is: manufacturers responsible for the replacement of new hot water submersible pumps and motors. (Note: the manufacturer is responsible for the replacement of the unit itself is not responsible for associated losses)
  Hot water submersible pump quality problem definition _ mainly from the material and performance of the hot water submersible pump quality requirements of the high hope of using a long life point, we should pay more attention to his material, like the stator height, silicon steel quality Cold rolling is better than cold rolling), the rotor shaft (good with stainless steel welding), as well as oil seals, which is very important for home use if the use of silicon carbide on the very good , Bearing is also very important, even if the brand is a human bearing, which is also divided into 369 and so on. You say the submersible pump, a relatively broad scope, at least talk about how much power, use of such information. Performance, then, you take the pump to test, look at his output power, head flow, speed load how, the same level of motor, high speed, light load.